leandro

Je comprend rien a ce que tu dit, y'a t'il un traducteur dans la salle lol, cest clair, faut en vouloir pour l aider !!!!!!!!!!!!! fait un effort Icekids !!!!!!

AS tu coché la case "Finaliser le dvd en ecriture" ? Si tu la pas fait , tu risque pas de faire lire ton backup par ta GC.

Ca confirme bien ce que je pensais. Avec ma V14 (violette) impossible de lire un backup sur mini DVd-r jusqu au bout , plantage systematique,meme apres reglage de la lentille. (en fait le mini dvd-r(8cm) s arrete de tourner d ou le plantage) par contre avec des dvd-r, exellent rien a dire , ca passe nickel, pas un plantage. Je pensse bien que cela ,vient du bios 0.3 comme avec les verssions se finissant par 8 et dont la maj vers le bios 0.4 devrais regler ce probleme.

va la y a des infos a prendre en compte : http://gueux-forum.net/index.php?showtopic=47861

non mais je viens d'acheter ma GC... j'ai besoin de me documenter un max, j'ai pas trouvé de site assez bien fourni pour commencer... tu en connaitrais??! va la , il est tres complet avec de bon tuto tres explicites. http://www.nintendomax.com/

oui ,c est bien des pockets que j ai utilisé . Ma verssion de GC est une 14 (la violette). Et mes isos(1go425 760 sous XP) sont rippé a partir de mes originaux et par moi meme . En tous cas le constat que j ai fait c est que les minis dvd-r pocket passe tres bien sur les GC noir (source : utilisateur de GC noir) J ai peut etre mal reglé la resistance de mon lect GC , va savoir .

hello ACH j aimerais juste savoir comment tu a procede pour avoir une valeur fixe de 277 et surtout comment tu as positionner(a quel endroit en fait) les pics de ton multimetre sur la resistance qui est sous le bloc optique de la GC. Impossible pour moi ,d avoir une valeur fixe , les chiffres change tous le temp. Merci d'avance pour ta réactivité. salut leandro et dsl pour le retard ^_^ sinon pour repondre a ta question, j'ai fais exactement comme sur la photo au debut du topic Alors je ne suis pas electronicien mais p-e que tu devarais essayer de changer les polarités, moi je me rappelle plus comment je l'ai placé... sinon essaye un autre ohmetre ( digital ) désolé je sais que sa t'avance pas a grand chose, mais c'est tout ce que je peu... allez a+. oki merci, c est sympa quand meme d avoir pris de ton temp pour me répondre

Aucun probleme pour la viper , si tu veus savoir quel revision tu as il faut que tu l ouvre et que tu compare ta carte mere avec celle sur les tutos ,va la : http://www.maxconsole.com/?mode=comments&newsid=3182

un bon translator via google fera tres bien l affaire non ?

Allez a cette URL: Tous y est bien représenté en photos de tres bonne qualité et surtout tres précise , surtout pour ceux qui ont du mal avec les differents connecteurs du capot http://www.elotrolado.net/showthread.php?s=&threadid=367111

hello ACH j aimerais juste savoir comment tu a procede pour avoir une valeur fixe de 277 et surtout comment tu as positionner(a quel endroit en fait) les pics de ton multimetre sur la resistance qui est sous le bloc optique de la GC. Impossible pour moi ,d avoir une valeur fixe , les chiffres change tous le temp. Merci d'avance pour ta réactivité.

1) la pluparts de backups NTSC passe sans probleme sur une GC pal 2) un systeme de menu tres clair 3) flashage de la puce direct via DVD-r 4) support des manettes sans fil 5)une exploration du support inséré est possible 6)des .DOl peuvent etre lancé 7)detail precis de la verssion de la Gc etc................ 7)et surement d autres choses que je ne manquerais pas de citer par la suite apres une exploration plus poussé .

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ±² ÄÄÄÄÄÄ ±² ÄÄÄÄÄÄÄÄÄÄ ±² ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³X °ÛßÜÜ °Ûßß ÜÛßß ²Ûß ßßÜ ²Û °ÜßÛ °Ü Û ²ÛßÛ °Ûßß X³ ³ ÛÛ Û Û ÛÛß ÛÛ Û ÛÛ ²ÛßÛ ÛÛ ÛÛ Ü ÛÛ Û ÛÛ Û ÛÛß ³ ³ ° ± ² Û ²Û ² Û ßÛ²Û ÛÛ ² ßÛ²± ßÛÛ² ßÛÜ ßÛ²Û ßÛ²Û ÛÛ²ß ßÛ²Û Û ² ± ° ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ ³ ³ ³ ³ - COBRA FOR VIPER GC V0.3 - ³ ³ ³ ³ 12th of january, 2005 ³ ³ ³ ³ ³ ³ Today is a big day for GC owners, as one of the best rated games (RE4) ³ ³ for the system was just released. To celebrate with you, we decided we ³ ³ would give you a new version of our Cobra BIOS. It allows PAL users ³ ³ to play their RE4 import, which was not possible with Cobra 0.2 ! ³ ³ ³ ³ What's the Cobra BIOS ? A special BIOS specially tailored for your ³ ³ Viper GC that allows yo to run your backups (and now homebrew code!) ³ ³ from the GC drive using DVD(-/+)R or Mini-DVD(+/-)R! ³ ³ ³ ³ So what do you need exactly ? ³ ³ - A Viper GC chip ³ ³ - This very flash file ³ ³ - Some Compatible Media and a DVD-burner ³ ³ ³ ³ ³ ³ WHAT'S NEW ? ³ ³ ³ ³ The software part was improved a lot while our low-level hackers had ³ ³ some great time in vacation :-) ³ ³ ³ ³ - NTSC Regionfix issue on PAL systems is fixed! ³ ³ - Wireless controller is now supported! ³ ³ - Added a real GUI ³ ³ - The following Cobra options can be changed (stored in Viper flash): ³ ³ - Default boot action ³ ³ - Boot action when the X-key is hold at boot time ³ ³ - Video mode of the Cobra GUI (doesn't change Games' video mode) ³ ³ - Behaviour of the lid sensor when booting Original BIOS ³ ³ - You can get detailed GC Version Info ³ ³ - You can explore the content of your GC discs (original and backups) ³ ³ and even DVDs with ISO9660 filesystem! ³ ³ - You can flash your Viper GC by burning the flash file on a DVD ³ ³ (but don't throw away your programmer in case of a bad flash! :-) ³ ³ - You can execute homebrew programs (.DOL) from DVD, and enjoy many ³ ³ already-released homebrew productions! ³ ³ ³ ³ ³ ³ USER MANUAL ³ ³ ³ ³ - Flash the Viper GC with this BIOS then remove the parallel port ³ ³ connector from the programmer. ³ ³ ³ ³ - Turn on your GC with an ORIGINAL DISC in the drive. ³ ³ If there's no Title Screen coming, but the original BIOS instead ³ ³ it's probably that you messed up your viper install:-) ³ ³ Check that it's clean (and no wires crossing each other etc...) ³ ³ If you have a black screen coming, it's probably because you have ³ ³ some wierd BIOS we don't support (and don't know about) yet. ³ ³ ³ ³ - While turning on your GC: ³ ³ - Hold Y to go to Main Menu (if it's not your Default Boot mode) ³ ³ - Hold X for the other boot mode (can be set in Config Menu) ³ ³ - Don't hold anything for Default Boot Action ³ ³ ³ ³ - Select "Boot DVD" if you want to play a backup / homebrew program ³ ³ from DVD. "Please wait..." should appear. then "SWAP DISC NOW" and ³ ³ the GC disc is stopped (and laser off). As soon as you see the disc ³ ³ is slowing down it's safe to remove the original disc and put your ³ ³ DVD-R instead. After a few seconds the drive will start to spin ³ ³ again and disc will boot (if you didn't have enough time to do the ³ ³ swap trick, turn off the GC and try again) ³ ³ ³ ³ - Remove the top of your GC if you want to use full-size DVD-R ³ ³ ³ ³ - Select "Original BIOS (Region Free)" if you want to play an original ³ ³ import Game. ³ ³ ³ ³ - Select "Original BIOS" if you want to play an original Game ³ ³ compatible with your GC region, or if you want to go into the ³ ³ Original BIOS menus. ³ ³ ³ ³ - Select "Configuration Menu" if you want to change your Cobra BIOS ³ ³ configuration. The options are quite self-explanatory. ³ ³ ³ ³ - Select "Disc Explorer" to enter what we belive is the best new ³ ³ feature in this BIOS! It allows you to browse the content or your ³ ³ original GC discs or DVDs (a swap trick is needed for them) ! ³ ³ Supported file systems are FST (GC File System) and ISO9660. ³ ³ Joliet encoding is not supported in ISO mode. ³ ³ ³ ³ - Enter "Disc Explorer" and select a .VGC file if you want to reflash ³ ³ your Viper GC without the need of the Parallel port programmer! ³ ³ ³ ³ - Enter "Disc Explorer" and select a .DOL file if you want to run ³ ³ a homebrew program! (You can put up to 1.4 GB of homebrew things on ³ ³ a disc. We hope this will give some inspiration to emu authors :-) ³ ³ Our DOL loader is not perfect for now and works for around half of ³ ³ the public homebrew programs. Here are some of the programs booting ³ ³ successfully: Kinderkram demo by Hitmen (you gotta see this), ³ ³ GC-Linux, Ascii Fighter, DVD Browser, CTR_GCS, CTR_SND, GBQ Gameboy ³ ³ emulator, PSOLoader "It's working" demo, Maze, Nitrorally, Yeti 3D ³ ³ 3D engine, Chip8 emulator, Snowlords game, Terranigma and probably ³ ³ many we missed! ³ ³ ³ ³ ³ ³ THE MEDIA ³ ³ ³ ³ The GC drive in its default state only eats high-quality DVD-R and ³ ³ a few MINI-DVD-R. But a couple of weeks ago, speedi from the afterdawn ³ ³ forums found a nice way to tweak the laser so it reads almost any burned³ ³ media including some DVD+Rs. We recommend doing this laser tweak if you ³ ³ have any problems reading your DVDs. We are no laser experts, in fact ³ ³ we think it would be more appropriate to just lower the value of the ³ ³ variable resistor instead of setting it to an absoulte given value, ³ ³ but lots of people including us have been using this laser tweek for a ³ ³ couple of weeks without any problem reported so far. ³ ³ ³ ³³ You don't need to encrypt the disc or use a special burner firmware ³ ³ to write the disc. Just burn your ISO/GCM (rename it to .ISO) with ³ ³ Nero (or any other tool). ³ ³ ³ ³ ³ ³ TROOBLESHOOTING ³ ³ ³ ³ Here are the current bugs we will fix in a future version: ³ ³ ³ ³ - Sometime the "SWAP DISC" message doesn't appear (or disc doesn't ³ ³ slow down/laser is still on). If this happen to you just turn off ³ ³ your GC and try again (ok, this is clearly our fault :-) ³ ³ ³ ³ - If sometimes after you swapped a disc there is a sync problem with ³ ³ the DVD-R and origial BIOS is not loading, then try again. If this ³ ³ happen very often, then you need a better media. ³ ³ ³ ³ - If the drive becomes idle for a couple of minutes, depending on the ³ ³ media you're using it might loose sync, and hang. This is also a ³ ³ bug of ours we will track. For now, if this happens to you, avoid ³ ³ "PAUSE MODE" in games. It almost never happens for people that don't ³ ³ have a ?8 Version. For more info about the issues with this version, ³ ³ keep on reading. ³ ³ ³ ³ - Audio Streaming: Some games use a special audio streaming mode ³ ³ that can be compared to CDDA. For now, the ISO of the file needs to ³ ³ be patched with 0rbital's great ViperTemporaryAudioFix 1.1+. If the ³ ³ ISO is not patched you'll have noise instead of music. We will try to ³ ³ fix this issue so no patching is required. But in case we do, YOUR ³ ³ PATCHED ISOS WILL BE FULLY COMPATIBLE and still work with music! ³ ³ (so forget what is written in the fixer nfo file). Don't run the fix ³ ³ on ISOs that don't need fixing as it will only destroy them :-) ³ ³ ³ ³ - Most multi-discs games are working, just play with Disc 1 until ³ ³ you're asked to change disc and make a save here. Then boot with ³ ³ Disc 2 instead. We started working on code to allow disc-change, ³ ³ and we'll integrate it in a new release. ³ ³ ³ ³ All those problems could be fixed in a next update. ³ ³ ³ ³ To know what's your GC Version code (2 digit number) go into Config ³ ³ Menu, then Version Info, 2nd page. First digit corresponds to GC ³ ³ mobo version, 2nd digit corresponds to drive version. ³ ³ ³ ³ There IS an issue with drive "8" and current BIOS. People with latest ³ ³ drive version can run backups, but get a lot of "Disc Errors". At first ³ ³ we thought it was some mechanical problem (different laser or so), but ³ ³ we got your hands on a 48 unit a couple of days ago (thanks Melan) and ³ ³ confirm it's 100% Cobra related! We already localized the problem and ³ ³ have a dirty-fix working! We'll work hard on making a clean fix and ³ ³ do the necessary testing (all "48" testing wasn't done by us directly), ³ ³ and you could expect a Cobra 0.4 version fully compatible with ?8 units ³ ³ within one week! It will then work fine on just every gc version. ³ ³ ³ ³ IF YOU MAKE BACKUPS, DON'T USE ANY "WIPE" TOOLS TO SAVE SPACE. Unless ³ ³ you know it's REALLY working. Most of thoses tools only work because ³ ³ the current pso loaders patch libraries routines to emulate DVD. But ³ ³ on REAL HARDWARE, each file/fst has to be aligned on a 4-byte boundary! ³ ³ Else nothing will work. Audio Files (for audio streaming) even need ³ ³ to be aligned on a 32kb-boundary ! So forget current "WIPE" tools until ³ ³ they are fixed. But note that Garbage is NOT NEEDED by the GC. The ³ ³ files must be correctly aligned that's it. So if your "WIPE" tool is ³ ³ not changing the image size (meaning there's no relocation) then it's ³ ³ probably fine. It is also possible to write a tool that re-aligns the ³ ³ files of a badly-wiped image. ³ ³ ³ ³ ³ ³ THE RUMORS ³ ³ ³ ³ We won't comment on the tons of rumors we read daily about the Cobra, ³ ³ we can just say that what you don't read here is not official. But we ³ ³ feel honored so many people decided to look at our code, too bad we ³ ³ didn't expect your visit or we'd have added some funny hidden messages! ³ ³ Depends on what your goal was, we made it even easier for you this ³ ³ time. Just hold Z at boot time :-) ³ ³ ³ ³ ³ ³ THE FUTURE ³ ³ ³ ³ We now have a 48 unit for a couple of days, and already found a fix for ³ ³ it so cleaning/testing/releasing it is now our main priority. ³ ³ Apart from that, we have written a complete Cheat System compatible ³ ³ with (decrypted) AR codes. Only the GUI for it has to be written now. ³ ³ (Maybe we can even support crypted codes if Parasyte allows us to ³ ³ integrate his great GCNcrypt tool into the Cobra? :-) ³ ³ We have lots of ideas to expand the Disc Explorer possibilities as ³ ³ well! ³ ³ ³ ³ ³ ³ CLOSING WORDS ³ ³ ³ ³ Special thanks to E*Flash for his help, RoM for the early units, ³ ³ Melan for the /48 GC and to everybody that tried Cobra V0.2 and posted ³ ³ constructive feedback. ³ ³ ³ ³ You are free to redistribute this package as long as it's not changed, ³ ³ patched, ported, or whatever. ³ ³ ³ ³ Our code is free of any copyrighted code from third party. ³ ³ It is also free of any GPL licensed code, we have strong respect for ³ ³ other people's hard work. We only ask you to show similar respect ³ ³ toward our work. To put it in other words, if you are in the "right" ³ ³ side, draw the line between learning and stealing. Thank you. ³ ³ ³ ³ That's it for this NFO, hope we didn't miss some important point. ³ ³ ³ ³ Have a nice day :-)

Deja commence, par la flashé et apres tu te poseras les bonnes questions une fois flashé le bios cobra doit apparetre, a l allumage de ta GC. Bien sur ,si tes soudures sont OK .

devisse les et ton programateur rentrera parfaitement dans ton port parallele oui obligatoirement sinon comment tu va flasher ta puce pour y mettre le bios

sa te servirais bien de lire un peu les postes precedents

ca confirme bien ce que je penssais dans mon topic precedent en tous cas avec la viper ca fonctionne a merveille . Ce soft sert a quelques jeux seulement , les autres fonctionne parfaitement.

http://www.ps2ownz.com/forums/attachment.p...tachmentid=3833 La sortie devrais etre imininente !!!!! comment j ai hate !!!!!!!!!!!!!!!!! Ce bios deviens de + en + complet !!!!!!!!!!!

merci pour toutes ces precisions et ta réactivité !!!!!!!!!!!!!!!!!! Ca me confirme bien que mes plantages sont du a mon lecteur .

oui j ai deja essayer cette methode , mais non toujours pareil. Par contre tu grave avec quel prg de gravure ?

tu veus dire quoi par R ?

hello je voudrais savoir si tu les a testé assez longtemp tes jeux ? bien sur en faite j'ai surtout joué a " Mario Party 4 (entre autre) " entre ami,sans probleme. /!\ mais hier j'ai tésté 2 jeux ils sont pas passé : Mario power tennis =->ecran noir aprés le logo Gamecube Zoids battle legend => nintendo present puis plus rien sinon les jeux qui sont passé chez moi sont (Mini-Dvd memorex,gamecube 16): Zelda Four Sword Mario super smash Bros melee Mario Party 4,5,6 Disney Party Final Fantazy Chronicles Harvest Moon Mario Kart DD Resident Evil 3 . . . Le resteplus tard Merci pour ta reponse , par contre peus tu me dire la couleur de ta GC la 16 cest une grise non ? Je te demande ca parce que moi les memorex y passe, puis le message classique "erreur de lecture" Cela dit j ai 6 boites si ca t interesse . ps : pour mario et zoid une maj du bios reglera surement ce desagrément.

A l avenir ce soft sera intégré en natif dans la viper et il me semble qu il na ete concu que pour la viper .

hello je voudrais savoir si tu les a testé assez longtemp tes jeux ?

With the GC PAL i found only a difference. After installation i see that i can boot only original PAL by pressing Y and Import games JAP and USA pressing X at the start of the Cube. Essaye ca et dit nous si sa marche