Hello World 2.0 -> 2.8


Cisco21
 Share

Messages recommandés

Voici le read me :

HELLO WORLD for Firmware 2.00-2.80

-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-

Finally, it's here! As of today, the world of homebrew is no longer restricted to owners of Grand Theft Auto.

Following the publication of a new proof of concept TIFF vulnerability by NOPx86, a team of PSP developers has been working hard to turn it into an opening for homebrew on the PSP. We're pleased to announce that the wait is over, with the release of a Hello World demo that runs on all PSP firmwares that are capable of viewing TIFF images!

To install, just unpack this ZIP file to your PSP's PHOTO folder, and then attempt to view hello_world.tif. Hello World will launch automatically. You may find that occasionally the full screen doesn't show - this is a known problem, just restart your PSP by holding the power button until it turns off, then open the image again. To quit, hold the power button until the PSP turns off.

So what happens next? This shows that we can run code via this exploit. It won't be too hard to develop an eLoader that can use this exploit on v2.0 - v2.6. v2.7+ will be harder, due to extra security, but will happen a little later. Kernel mode is unavailable on v2.8, but it is likely that a downgrader is possible on all other firmwares. But then, with the possibility of kernel homebrew running without the need for a game UMD, why would you need to downgrade?

Full credit is given in the Hello World, but repeated here: Thanks to NOPx86 for the initial proof of concept on the x86 processor, and psp250, Skylark, Joek2100, CSwindle, JimP and Fanjita for the PSP work. Thanks also to Ditlew, HarleyG and our families for general support during this work.

Et le dl : http://files.fanjita.org/psp/helloworld_all.zip

Lien vers le commentaire
Partager sur d'autres sites

Apparemment ....

Accès kernel sur les 2.71 (donc le même potentiel qu'une 1.5) mais pas certain sur les 2.8

Sur les 2.80 il n'y a pas d'accès au kernel :( donc pas de possibilités pour les loaders d'iso... Dommage :ninja: ! Cela dit c'est tout de même cool ^_^ j'espère que ça va continuer à avancer :D:sorcerer: !!!

Édit: désolé je viens de m'apercevoir que c'était marqué au dessus :) désolé :fou:

Modifié par SonicX
Lien vers le commentaire
Partager sur d'autres sites

Je l'ai testé.

Ca marche mais ça ne se lance pas toujours à 100%.

Du manière générale, il vaut mieux enlever le disque s'il y en a un dans la PSP, car j'ai noté qu'il y avait beaucoup de chance pour freezer ou blackouter sa PSP (mais rien de fatal, juste qu'il faut éteindre complètement sa PSP).

Si les conditions sont bonnes (genre, pas de tâche en arrière fond qui pourrait être pertubé par la faille, sans doute), le helloworld se lance juste après l'appui sur le bouton X (pour accèder au répertoire contenant l'image TIFF avec faille), et là surprise vous avez un texte qui serpente et qui n'a rien d'un logiciel de $ony : du code NON signé $ony a été lancé !

Combinée avec la faille du kernel applicable jusqu'à la version 2.71 (faille dévoillée après la sortie de ces firmwares si je me souviens bien), on n'a pas de mal à envisager un eloader et un downgrader dans les prochaines semaines. Il suffit de se rappeler ce qui s'est passé pour le downgrader 2.5/2.6->1.5 qui est sorti peu de temps après la "découverte" de la faille kernel.

Donc je garde espoir.

NOTA BENE : je suis en 2.7

Modifié par hlide
Lien vers le commentaire
Partager sur d'autres sites

On doit pas lire le meme thread :

"So what happens next? This shows that we can run code via this exploit. It won't be too hard to develop an eLoader that can use this exploit on v2.0 - v2.6"

Ca veut bien dire :

"Et que se passera-t-il apres ? Ceci montre qu'on peut faire tourner du code via cet exploit. Ce ne sera pas trop difficile de developper un eLoader qui pourrait utiliser cet exploit en v2.0-v2.6"

Lien vers le commentaire
Partager sur d'autres sites

Créer un compte ou se connecter pour commenter

Vous devez être membre afin de pouvoir déposer un commentaire

Créer un compte

Créez un compte sur notre communauté. C’est facile !

Créer un nouveau compte

Se connecter

Vous avez déjà un compte ? Connectez-vous ici.

Connectez-vous maintenant
 Share